PROFILES AND ACCESSORIES

SCHIENE - Edge profile for floor coverings.

Schluter Schiene - edge floor profile for floor covering
  • Schluter SCHIENE is designed to provide edging for tile coverings. Typical applications include edge protection where tile is bordered by carpet, at expansion joints, or as a decorative edging for stairs.
  • Schluter SCHIENE is available in stainless steel, solid brass, aluminum, and anodized aluminum. The profile features a trapezoid perforated anchoring leg, which is secured in the mortar bond coat beneath the tile, and an 87° sloped vertical wall section that transfers point loads to the substrate and surface covering while protecting the tile edges from damage.
  • Schluter SCHIENE, in solid brass, aluminum, and anodized aluminum, features a 5° sloped top flange and fillet at the anchoring leg/vertical section interface to enhance edge protection by reducing stresses on the tile, and, in sizes greater than 1/4" (6mm), features an integrated joint spacer that establishes a defined joint cavity between the tile and the profile. Schluter SCHIENE, in stainless steel, is roll-formed and does not feature an integrated joint spacer.
  • The anchoring leg of Schluter SCHIENE, in all materials, is available with a special radius perforation "R" so that the profile can be used to form curves.
  • SCHIENE A - Aluminium.
  • H = 6, 8, 10, 12.5, 15mm. L = 2500mm.
  • SCHIENE AE - Anodised aluminium.
  • H = 10mm. L = 2500mm.
  • SCHIENE E - Stainless steel.
  • H = 6, 8, 10, 12.5, 15mm. L = 2500mm.
  • SCHIENE M - Brass.
  • H = 6, 8, 10, 12.5, 15, 20, 25mm. L = 2500mm.
  • SCHIENE PERFORATED - Aluminium or stainless steel.
  • H = 10, 12.5mm. L = 2500mm.

RENO-U - Smooth transition between tile coverings and floor coverings.

Schluter Reno-U - smooth transition between tile and floor covering
  • Schluter RENO-U is designed to provide a smooth transition between tile coverings and floor coverings at lower elevations or finished concrete.
  • The profile is available in solid brass (stainless steel, anodised aluminum and Tuscan color coated aluminum - only special order). Schluter-RENO-U features a trapezoid perforated anchoring leg, which is secured in the mortar bond coat beneath the tile, and a sloped surface (approximately 25°) that eliminates trip hazards and protects tile edges.
  • The leading edge of the profile abuts the lower surface covering, typically VCT. Schluter RENO-U, in solid brass and anodised aluminum features an integrated joint spacer that establishes a defined joint cavity between the tile and the profile. Schluter RENO-U, in stainless steel is roll formed and does not feature an integrated joint spacer.
  • In installations where the leading edge abuts a lower surface covering, all sizes of Schluter RENO-U, except the 3/4" (20mm) and 11/16" (17.5mm), are compliant with the Americans with Disabilities Act (ADA).
  • In installations where the leading edge rests on top of the lower floor covering, the 3/4" (20mm), 11/16" (17.5mm), and 9/16" (15mm) sizes are not ADA compliant.
  • RENO-U - Brass
  • H = 8, 10, 12.5mm. L = 2500mm.

RENO-RAMP - Smooth transition where wheel carts are used.

Schluter Reno-Ramp - smooth transition floor profile
  • Schluter RENO-RAMP is designed to provide a smooth transition between tile coverings and floor coverings at lower elevations or finished concrete, particularly in commercial applications where wheel carts are used (e.g., bakeries, hospitals, etc.).
  • The profile is available in anodised aluminum. RENO-RAMP features a trapezoid perforated anchoring leg, which is secured in the mortar bond coat beneath the tile, and a sloped transition surface that terminates at the height of the tile edge. The profile protects tile edges and provides a sloped surface to eliminate trip hazards and allow easy access for wheel carts. RENO-RAMP features an integrated joint spacer that establishes a defined joint cavity between the tile and the profile.
  • All sizes of RENO-RAMP, except sizes 9/16" (15mm) and 3/4" (20mm), are compliant with the Americans with Disabilities Act (ADA).
  • RENO-RAMP - Anodised aluminium.
  • H = 12.5mm. L = 2500mm.

JOLLY AC and P - Finish and protection of external wall corner.

Schluter Jolly AC and P - external wall corner protection
  • Schluter JOLLY is a finishing and edge protection profile for the outside corners of tiled surfaces.
  • It features a trapezoid perforated anchoring leg that is secured in the mortar bond coat beneath the tile, and an 87° sloped vertical wall section that provides a decorative finish and protects adjacent tiles.
  • The profile is available in colour coated aluminum and PVC.
  • JOLLY AC - Colour coated aluminium - Brilliant white.
  • H = 6, 8, 10mm. L = 2500mm.
  • JOLLY P - Coloured PVC - White
  • H = 6, 8, 10, 12.5mm. L = 2500mm.

ROUNDEC E - Stainless rounded profile for external corners.

Schluter Roundec E - stainless rounded profile for external corners
  • Schluter RONDEC is a finishing and edge-protection profile for the outside corners of tiled surfaces. It features a trapezoid perforated anchoring leg that is secured in the mortar bond coat beneath the tile and a reveal that forms a symmetrically rounded outer corner with 1/4" (6mm) radius along the surface edge.
  • The profile is available in stainless steel (solid brass, chrome plated solid brass, color coated aluminum, anodized aluminum, Tuscan color coated aluminum and PVC - only special order).
  • In addition to its decorative effect, the profile protects tile edges against damage caused by mechanical stresses. Schluter RONDEC, in stainless steel, is particularly resistant to wear when used as edge protection. It may also be used as a stair nosing or transition profile.
  • In addition Schluter RONDEC is also suitable for transitions, corners, or dado coverings with other covering materials for example: carpet, parquetry, natural stone tiles, or cold cured resin coverings. The integrated joint spacer forms a defined joint cavity with the tile.
  • Note: Schluter RONDEC, in stainless steel, does not feature the integrated joint spacer. Matching inside and outside corners, including sink corners, and connectors are available.
  • RONDEC E - Stainless steel.
  • H = 6, 8, 10, 12.5mm. L = 2500mm.

TREP E - Stainless steel stair nosing with a slip resistant surface.

Schluter Trep E - stainless steel stair nosing profile with a slip resistant surface
  • Schluter TREP-E is designed to protect tiled stair edges and provide an easily visible, slip-resistant wear surface for durable, safe, and visually appealing stair nosing design. The profile is made of attractive and durable stainless steel, making it particularly suited for areas subjected to heavy foot traffic, such as offices or public buildings.
  • TREP-E can be integrated into stairs covered with tile or natural stone, as well as into a screed or a surface coating that is a minimum 3/32" (2mm) thick via the trapezoid perforated anchoring leg. When integrated into screed layers, the anchoring leg of the profile must be covered with at least 9/16" (15mm) of mortar.
  • The Schluter TREP-E wear surface meets or exceeds the coefficient of friction recommendation in the Americans with Disabilities Act (ADA), for use in applications where the risk of slipping exists (Tile Council of North America (TCNA), test method ASTM C 1028, .66 wet or dry).
  • Matching end caps are available.
  • TREP E - Stainless steel.
  • H = 11mm. L = 2500mm.

DILEX - Movement and control joint profiles.

  • Schluter DILEX screed joint profiles are designed to provide movement joints in tile installations that are set in a mortar bed (e.g., ceramic tile, natural stone, pavers, and agglomerate tile). These profile systems are placed to produce individual fields in the assembly and feature flexible central zones to accommodate movement.
  • Schluter DILEX mortar bed joint profiles may also be inserted in saw-cut joints or wider joints; for example, in the case of renovations. The remaining joint between the tile and the profile must be filled completely with grout or epoxy. The side sections of the profiles, made of rigid PVC, protect the edges of the adjacent covering against mechanical stresses caused by industrial traffic. However, where heavy mechanical stresses are anticipated, limitations of the PVC as edge protection must be considered.

DILEX MOP

Schluter Dilex MOP - expansion joint profile
  • Schluter DILEX - MOP is an expansion joint profile with serrated sidewalls made of rigid, recycled PVC and grey, soft PVC expansion zone for use in screed applications.
  • DILEX - MOP - PVC (grey).
  • H = 50mm. L = 2500mm.

DILEX MKS

Schluter Dilex MKS - expansion joint profile
  • Schluter DILEX - MKS is a movement profile with edge protection consisting of lateral anchoring legs made of brass, which are connected to a replaceable movement zone made of soft rubber.
  • DILEX - MKS - brass.
  • H = 8, 10, 12.5mm. L = 2500mm.

DILEX BWB

Schluter Dilex BWB - expansion joint profile
  • Schluter DILEX - BWB is a movement joint profile with side section of rigid, recycled plastic. The top movement zone is made of soft CPE and creates the 10mm wide visual surface.
  • DILEX - BWB - plastic.
  • H = 6, 8, 10, 12.5, 15mm. L = 2500mm.

DILEX BWS

Schluter Dilex BWS - expansion joint profile
  • Schluter DILEX - BWS is a movement joint profile with side section of rigid, recycled plastic. The top movement zone is made of soft CPE and creates the 5mm wide visual surface.
  • DILEX - BWS - plastic.
  • H = 6, 8, 10, 12.5mm. L = 2500mm.

DILEX BWA

Schluter Dilex BWA - expansion joint profile
  • Schluter DILEX - BWA provides a flexible connection between tiled surfaces and existing coverings or structures such as door and window frames.
  • DILEX - BWA - plastic.
  • H = 6, 8, 10mm. L = 2500mm.

DILEX EKE

Schluter Dilex EKE - expansion joint profile
  • Schluter DILEX EKE is a corner movement profile that effectively absorbs movement at inside wall corners and at floor/wall transitions in applications where no large movement is expected.
  • DILEX - BWA - plastic and CPE (white and grey).
  • H = 8, 11mm. O = 7mm L = 2500mm.

DILEX EK

Schluter Dilex EK - expansion joint profile
  • Schluter DILEX EK is two piece profile with a tongue and groove connection for permanently flexible corner joints at floor/wall transitions and skirting.
  • DILEX - BWA - plastic and CPE (grey).
  • H = 11mm. O = 10mm L = 2500mm.

DILEX AS

Schluter Dilex AS - expansion joint profile
  • Schluter DILEX AS is a pre-fabricated two part profile for the flexible connection of tiled surfaces to building fixtures, i.e. bathtubs, pre-fabricated shower trays, as well as door and window frames.
  • DILEX - BWA - plastic and CPE (grey).
  • H = 11mm. O = 10mm L = 2500mm.

REMA

Schluter Rema - tile magnets system for creating concealed acces panels in tiled wall coverings
  • Schluter REMA is the ideal system for creating concealed access panels in tiled wall coverings.
  • Schluter REMA’s installation is independent of tile size and thickness and enables exact matching of the access panel to the overall joint design. Thus, panels that access electrical or plumbing components, for example, do not spoil the visual appearance of the tiles.
  • Box include:
  • 4 magnets and 4 counter plates.
go to the top